Aktivität von Maximilian Seesslen
von 25.09.2022 bis 24.10.2022
23.10.2022
-
09:40 sensemux Wiki-Bearbeitung: Results (#59)
22.10.2022
-
-
21.10.2022
-
-
20.10.2022
-
-
19.10.2022
-
-
-
-
-
18.10.2022
-
16.10.2022
-
-
15.10.2022
-
-
-
-
-
- return ADC value 0 and set heartbeat led to error blinking.
-
- Reason unclear.
At least the "trouble"-mechanism of sensemux could be used to indicate the problem via LED.
Assum... -
- Error in App-file; CS was not used.
-
-
14.10.2022
-
- Test fails.
Size is "0".
Did the previous test report work?
-
-
-
13.10.2022
-
-
-
- Sometimes its enough to know that it is dirty and there are changes to version tag. But there might not be enough spa...
-
- Not enough space. Implement a compact string in libcampo.
-
- I did not even mark the PCB :/
-
- Reason unclear.
At least the "trouble"-mechanism of sensemux could be used to indicate the problem via LED.
Assum...
12.10.2022
-
-
- The layout is strange at the moment; redundant fields.
2Byte Article/Family (e.g. Minutnik-Oled, Minutnik-eInk, Mi... -
-
-
-
11.10.2022
-
-
- duplicate
-
- Can't write hwdata this way.
Working with debugger still works; i can hold and continue so pins are not completely m... -
"gdb_breakpoint_override hard" had to be set in openocd target file.-
- Depending on breakpoints gdb can call specific commands by itself;...
-
- Halting and continuing is working so general SWD-Pin-Configuration is not totally bad.
* Is openocd showing valid ... -
10.10.2022
-
-
-
-
-
-
-
-
-
-
-
09.10.2022
-
08.10.2022
-
07.10.2022
-
-
-
-
-
-
-
-
-
-
-
-
-
06.10.2022
-
-
-
-
-
-
-
-
-
-
-
- When device is running on USB, the behaviour should be different.
* Fancy intro
* No timers can be started
* LED... -
- This can be done via heartbeat LED.
Having the LDO-LED as generic "on"-LED on GPIO makes sense to visualise crashed ... -
- Disabling debigging in standby does the trick.
-
- Workaround works.
As described in the stm32 errata, the device can not be powered off when usb is connected (WKUP2 s... -
- Just disable debug in standby mode.
-
- Just disable debug in standby mode.
According to "reference manual":https://www.st.com/resource/en/reference_manual/... -
05.10.2022
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
- E.g. the NJRST is internally connected to an pullup when in standby.
When an LED is connected it can be seen.
If su... -
- No tests have been berfomed yet.
* Setup a further PCB (v0.1.x), only for measurements
* measure current on stand... -
- The drawText-function does not support fonts on SPI-Flash.
Not needed at the moment?
-
- An alarm-function would be really nice and a killer-feature towards miniminutnik.
The alarm could even be displayed ... -
- It only shows "charge"-LED
Not really usefull. But the LDO-LED could be replaced.
Usefull to indicate the mode; con... -
-
- Configuration in internal EEPROM missing.
-
"Errata1":https://www.st.com/resource/en/errata_sheet/es0125-stm32l151x68b-and-stm32l152x68b-device-errata-stmicroe...-
- The JTAG-RESET has an weak permanent pullup. So the connected LED glows in standby causing battery discharge when dev...
-
- USB-Detect-Input is floating when USB is not connected.
Internal Pulldown has to be used for Wakeups.
-
- * Crystal is missing
* Is reconfiguration of the Sysclock-configuration working? Only use HSE when USB connection is...
30.09.2022
-
- An generic command that can be connected to methods of an class.
This makes it very trivial to implement an comprehe...
29.09.2022
-
28.09.2022
-
26.09.2022
-
-
-
-
-
-
-
25.09.2022
-
-
-
-
-
Auch abrufbar als: Atom