Redmine

15.02.2024

15:48 libcampo Feature #491 (Erledigt): Vagus: implement command to switch to bootloader

Option-Bytes are used in first test.
Maximilian Seesslen

11.02.2024

09:04 CANSwitch Test #489 (Neu): Send keep-alive

When changing illumination, an keep-alive event should be send. Maximilian Seesslen

08:51 CANSwitch Test #488 (Neu): Fading out before timeout

Maximilian Seesslen

08:50 CANSwitch Test #487 (Erledigt): Fading working

Maximilian Seesslen

07:43 CANSwitch Test #486 (In Bearbeitung): timeout warning

Maximilian Seesslen

07:43 CANSwitch Test #486 (Erledigt): timeout warning

Maximilian Seesslen

07:42 CANSwitch Test #486 (In Bearbeitung): timeout warning

Maximilian Seesslen

07:43 CANSwitch Test #485 (In Bearbeitung): Timeout

Maximilian Seesslen

07:43 CANSwitch Test #485 (Erledigt): Timeout

Maximilian Seesslen

07:40 CANSwitch Test #485 (Erledigt): Timeout

Maximilian Seesslen

05.02.2024

22:56 Mainswitch Feature #347 (Erledigt): Send battery level via CAN

Maximilian Seesslen

22:54 Mainswitch Feature #479 (Erledigt): Check behaviour when device is immediately shut off before button release

Maximilian Seesslen

22:51 Mainswitch Requirement #478 (Erledigt): LED States

Maximilian Seesslen

22:51 Mainswitch Requirement #481 (Erledigt): Send Event-error when battery is too low

Maximilian Seesslen

22:11 Mainswitch Requirement #480 (Erledigt): Configurable auto-off timeout

Maximilian Seesslen

22:02 Mainswitch Requirement #482 (Erledigt): Pseudo-Off

Maximilian Seesslen

22:02 Mainswitch Requirement #483 (Erledigt): Wait for button-release on shutdown

Maximilian Seesslen

21:51 Mainswitch Requirement #483 (Erledigt): Wait for button-release on shutdown

When shutdown via button is triggered, a state has to wait untill the button is released.
Otherwise the device would... Maximilian Seesslen

01.02.2024

18:37 Mainswitch Requirement #482 (Erledigt): Pseudo-Off

Due to non-functional WKUP, the first boards should not got to standby because
they can not be woken up any more.
... Maximilian Seesslen

18:01 Mainswitch Requirement #481 (Erledigt): Send Event-error when battery is too low

Target voltage is 2,4V.
Check should be done every 15min.
Error should be send at 2,2V (end-point voltage of NiMH i... Maximilian Seesslen

17:48 Mainswitch Requirement #480 (Erledigt): Configurable auto-off timeout

After an configurable ammount of time, the device should automatically turn off.
The 'off' is an hard power-off. O... Maximilian Seesslen

17:29 Mainswitch Feature #479 (Erledigt): Check behaviour when device is immediately shut off before button release

I assumed that the device will immediately repower on when shutting down while button is still pressed.
Has to be ve... Maximilian Seesslen

17:27 Mainswitch Requirement #478 (Erledigt): LED States

* The LED is permanent on in operational mode
* The LED is blinking normal when shutdown was initiated by holding bu... Maximilian Seesslen

19.01.2024

17:47 campoTemplate Fehler #474 (Neu): Git history is not reset

Its confusing to have already taged versions.
Maximilian Seesslen

15:21 campoTemplate Fehler #473 (Neu): There is no actual template for README.md

The README.md is about "campoTemplate" itself. Not very problematic because the templates
README would be quite empt... Maximilian Seesslen

18.01.2024

14:40 mainSwitch Fehler #472 (Abgewiesen): Wakeup-Button is not working

In normal operation this is no issue because its an normyl power cycle.
But when the device is still powered by anot... Maximilian Seesslen

13:29 mainSwitch Fehler #471: Wakeup-Button is not working

PB1 is no WKUP at all!
Others WKUP-pins in the arena file have to be checked. Maximilian Seesslen

13:25 mainSwitch Fehler #471 (Neu): Wakeup-Button is not working

In normal operation this is no issue because its an normal power cycle.
But when the device is still powered by anot... Maximilian Seesslen