Software » Campo

h1. Intro

With the TDT-Protocol sensors can just send their values on the BUS without complex object catalogue.

An monitor-software is able to display values without knowing anything about the sensors or their configuration.

The CANId cinsists of an function code and the node id. Like CANOpen the function code is 4 Bits and the Node-ID is 7 Bit.

In CAN2.0A there can only be 128 Nodes.

CAN 2.0A: 0..0x7FF

CANOpen: 4 Bit Function code, 7 Bit Node-ID

Node-Id: 0..0x7F

Function-Code Mask: 0x780

There are 14 or 28 Filters on STM32Fs

Some STM32 have an internal 96-bit unique ID.

h2. Function code

|_. Code |_. Decription    |_. Examples             |

| 0x0    | NMT-Write       |                        |

| 0x1    | NMT-Send        |                        |

| 0x2    | Alarms          |                        |

| 0x3    | Write object    | Set Date, illumination |

| 0x4    | Read object     | Get product codes      |

| 0x5    | Send object     | Send temperature       |

| 0x6    | Resend object   | Replay recorded data   |

| 0x7    | data blob       |                        |

h1. IDs, ranges and commands

h2. Node IDs

* 11-Bit-Identifier, (CAN 2.0A); 2048; 0x0 ... 0x7F0; 0x0 ... 0x7F with function code

* 29-Bit-Identifier, (CAN 2.0B); 0x20000000

|_. Range      |_. Decription           |_. Examples              |

| 0x01-0x0F    | Network Manager        | PC                      |

| 0x10-0x2F    | Active controller      | CANDis                  |

| 0x30-0x4F    | Actor                  | CANSwitch               |

| 0x50-0x6F    | Sending sensors        | Sensemux, CANIO         |

| 0x70-0x7F    | Passive Sensors        | CANRec                  |

h2. Object structutre

|_. Size |_. Decription |_. Examples                                                       |

| 2      | Object       | Plain Sensor value; Set illumination                             |

| 1      | Data type    | Int, Float, Time, Date, Percent, Promil, Multipacket-String      |

| 1      | Unit         | Hz, °C, Time, Date, PWM, CAN-ID, Name, Description, Room         |

| 4      | Value        | 32Bit                                                            |

h2. Objects

|_. Code                  |_. Description             |

| none                    |                           |

| ambientLight            |                           |

| plantLight              |                           |

| multimediaSwitch        |                           |

| mainSwitch              |                           |

| date                    |                           |

| time                    |                           |

| dummy                   |                           |

| plantSensor             |                           |

| plantSensor [0-7]       |                           |

| firmwareVersion         |                           |

| firmwareDate            |                           |

| hardwareRevision        |                           |

| hardwareDate            |                           |

| temperatureIntern [0-7] |                           |

| temperatureExtern [0-7] |                           |

| humidity                |                           |

| VOC                     |                           |

| Replay                  |                           |

| Data-Dump (SD-Card)     |                           |

h2. Units

* Date: year 2B, month 1B, day 1B

* Time: hour 1B, minute 1B, second 1B, subsecond 1B

h2. Example: Turn on the lights

|_.Data   |_.Size   |_.Description                              |

|0x300    | 29 Bits | Function code: Write Object; All objects. |

|0x0      | 2 Byte  | Message-Type: Global command              |

|0x1      | 1 Byte  | Data-Type: Permill                        |

|0x1      | 1 Byte  | PWM: PWM permilli                         |

|1000     | 4 Byte  | Value: Full Brightness                    |

h1. Multipacket-Strings

There should be the posssibillity to write the complete SPI-Flash even if it takes forever.

Not every slave needs to be able to send super big blocks. But every slave should be able to

send e.g. descriptions.

There can not be multiple transfers at the same time from one node because there is no identification.

|_. Size    |_. Type                                           |

| 0x4       | Package number (0: Data contains package count)  |

| 0x4       | Data                                             |

h2. Header

|_. Size    |_. Type           |

| 0x4       | Total size       |

| 0x4       | Type (1=SDCard)  |

| 0x4       | Target node ID   |

| 0x4       | CRC32 of data    |

h2. Example: CANRec

PC requests an complete dump from single Node. Node will just stream it out.

h1. NMT

h2. Actuator introduction

When introduction is requested by system command, each device must send an description.

|_. Size |_. Decription |_. Examples                                                       |

| 2      | Object       | Object                                                           |

| 6      | MAC/Unique ID| 48Bit                                                            |

h3. Objects

|_. Size |_. Decription          |

|1       | Request intoruction   |

|2       | MAC low               |

|3       | MAC high              |

|4       | Protocol versions     |

|5       | Firmware version      |

|6       | Product Code          |

|7       | Node-Id               |

h3. Protocol versions

|_. Size |_. Decription            |

|1       | TDT Major               |

|1       | TDT Minor               |

|1       | NMT Major               |

|1       | NMT Minor               |

|1       | Blob Major              |

|1       | Blob Minor              |

h1. V2

|_. Size |_. Decription |_. Examples                                                       |

| 1      | Packet type  | Standard TDT packet                                              |

| 1      | Sub-Id;      | Futher index; Sub-Sensor or more specifi kind of thing to be set |

| 1      | Data type    | Int, Float, Time, Date, Percent, Promil, Multipacket-String      |

| 1      | Unit         | Hz, °C, Time, Date, PWM, CAN-ID, Name, Description, Room         |

| 4      | Value        | 32Bit                                                            |

h1. V3

|_. Size |_. Decription |_. Examples                                                               |

| 2      | Object       |                                                                          |

| 1      | Sub-Id;      | Flags, Subid                                                             |

| 1      | Unit/Type    | Hz_int, °C_centi, Time, Date, PWM_milli, CAN-ID, Name, Description, Room |

| 4      | Value        | 32Bit                                                                    |

h2. Flags

4 Bit multi message count

4 Bit multi message pos

Length in Bytes given via CAN?

Strings with max. 64 characters.

h2. Multimessage package

There should be the possibillity to write the complete SPI-Flash even if it takes forever.

Not every slave needs to be able to send super big blocks. But every slave should be able to

send e.g. descriptions.