Aktivität
von 07.10.2022 bis 05.11.2022
05.11.2022
-
20:59 Biwak Revision a813131b (libbiwak3): updated font
-
-
-
03.11.2022
-
-
15:02 Minutnik eInk Fehler #298 (Erledigt): Temperature-Sensor, Flash etc are permanently on VDD
- There is already an switch for Display.
Temperature-sensor and FLASH can be connected to this power source.
Need ...
02.11.2022
-
- The BOOT-Resistor was way too high (1M Ohm).
Replace it with 10K-Ohm worked.
-
-
- Show either the serial number or the device alisa name on the display.
-
-
- It was the STOP mode in delay() which reseted periphery.
01.11.2022
-
-
-
31.10.2022
-
-
- Seems the very high BOOT-resistor was the problem.
29.10.2022
-
-
- Actually not needed but implemented.
The values are quite close.
Serno.1: 4031
Serno.2: 4029
-
-
28.10.2022
-
- Could reproduce it also with serno.1.
The disturbtion on VDD is quite high when USB is connected (ca. 24ns breakdown... -
- This can be added to bringup tests.
-
- Device should be able to calibrate itself and store the values in eeprom.
-
- One additional testpoint for 3V would help to measure power consumtion of MCU side.
26.10.2022
-
- Is USB power to low?
-
- Route the ground to an GPIO so it can be disabled and will be disabled when powered off.
Or even use an NMOS.
I m... -
- This is only noticable with lighttramitters which blocks/diffuse some light.
25.10.2022
-
- Device No.1 can not reproduce this.
Maybe Brownout-detection fails. Check other groups.
OB_BOR_LEVEL3: Supp... -
- Duplicate
19.10.2022
-
-
-
-
-
18.10.2022
-
-
17.10.2022
15.10.2022
-
- return ADC value 0 and set heartbeat led to error blinking.
-
- Reason unclear.
At least the "trouble"-mechanism of sensemux could be used to indicate the problem via LED.
Assum... -
-
- Error in App-file; CS was not used.
-
-
-
-
14.10.2022
-
- Test fails.
Size is "0".
Did the previous test report work?
-
-
-
13.10.2022
-
-
-
- Sometimes its enough to know that it is dirty and there are changes to version tag. But there might not be enough spa...
-
- Not enough space. Implement a compact string in libcampo.
-
- I did not even mark the PCB :/
-
- Reason unclear.
At least the "trouble"-mechanism of sensemux could be used to indicate the problem via LED.
Assum...
12.10.2022
-
-
- The layout is strange at the moment; redundant fields.
2Byte Article/Family (e.g. Minutnik-Oled, Minutnik-eInk, Mi... -
-
-
11.10.2022
-
- duplicate
-
- Can't write hwdata this way.
Working with debugger still works; i can hold and continue so pins are not completely m... -
"gdb_breakpoint_override hard" had to be set in openocd target file.-
- Depending on breakpoints gdb can call specific commands by itself;...
-
- Halting and continuing is working so general SWD-Pin-Configuration is not totally bad.
* Is openocd showing valid ... -
09.10.2022
-
-
-
-
08.10.2022
-
-
-
-
-
-
-
Auch abrufbar als: Atom