Eval » Historie » Version 11
Redmine Admin, 13.12.2021 12:56
| 1 | 1 | Redmine Admin | h1. Eval |
|---|---|---|---|
| 2 | |||
| 3 | * FPC 10p cable for CANIO/Miniminutnik |
||
| 4 | 8 | Redmine Admin | * Buchsenleiste: TX/RX/POW/I2C |
| 5 | 2 | Redmine Admin | * Boot/Reset button; gross |
| 6 | * 4Pin I2C-JST-Stecker |
||
| 7 | 1 | Redmine Admin | * TX/RX-LEDs (from adapter) |
| 8 | * Power-LED |
||
| 9 | * Target-LED |
||
| 10 | * Micro-USB |
||
| 11 | * Aussparung FPC-Stecker-Verrigelung |
||
| 12 | 8 | Redmine Admin | * 1mm Acryl schon sehr windig, siehe CANDis platten. Aber geht? |
| 13 | 1 | Redmine Admin | * MCP2221 |
| 14 | * LDO 3V |
||
| 15 | 2 | Redmine Admin | * Schiebeschalter: I2C Power 5V/3V |
| 16 | 10 | Redmine Admin | * LED power target |
| 17 | 1 | Redmine Admin | |
| 18 | 6 | Redmine Admin | VUsb must have bypass capacitor between 0.22 and 0.47 μF. _> 3x100nF |
| 19 | 1 | Redmine Admin | When using internal LDO, GPIO and UART signals are 5V. We dont want this-> extern LDO |
| 20 | 4 | Redmine Admin | |
| 21 | vom Design Links USB rein, rechts FPC raus. |
||
| 22 | 1 | Redmine Admin | LEDs vorne. Pinheader hinten oben. JST vorne. |
| 23 | Konnektoren alle oben, IC unten (1mm) _> 6mm total height |
||
| 24 | |||
| 25 | 10 | Redmine Admin | LED-Löcher von unten mit Uhu auffuellen? |
| 26 | |||
| 27 | 8 | Redmine Admin | h2. Buchsenleiste |
| 28 | |||
| 29 | |GND| |
||
| 30 | |3V | |
||
| 31 | |5V | |
||
| 32 | |RX | |
||
| 33 | |TX | |
||
| 34 | |SCL| |
||
| 35 | |SDA| |
||
| 36 | 1 | Redmine Admin | |GND| |
| 37 | 10 | Redmine Admin | |
| 38 | h2. LEDs |
||
| 39 | |||
| 40 | |VUSB |GRN | |
||
| 41 | |POW LDO|GRN | |
||
| 42 | |Target |VIO | |
||
| 43 | |RX |RED | |
||
| 44 | |TX |YEL | |
||
| 45 | 11 | Redmine Admin | |
| 46 | ---------------------- |
||
| 47 | | PINHEADER | |
||
| 48 | |USB O O FPC| |
||
| 49 | | ...... O O| |
||
| 50 | --JST----------------- |