Eval » Historie » Version 2
Maximilian Seesslen, 06.10.2022 15:05
| 1 | 1 | Maximilian Seesslen | h1. Eval |
|---|---|---|---|
| 2 | |||
| 3 | * Big LEDs to test outputs / Backlight-PWM |
||
| 4 | * Amplified Buzzer to test buzzer output directly on MCU |
||
| 5 | * PWM output to test buzzers; 3V; normal and amplified |
||
| 6 | * Test for CANBus-cables; |
||
| 7 | ** MCU with 4 inputs |
||
| 8 | ** 4 outputs to control which line to be tested to detect shortcuts |
||
| 9 | ** 4 outputs for LEDs to indicate errornous wire |
||
| 10 | ** How detect shortcuts |
||
| 11 | ** Button to reset |
||
| 12 | * Durchgangsprüfer ( buzzer-out / Buzzer-in ) |
||
| 13 | ** Do i really need this? Dont want to setup an multimeter |
||
| 14 | ** Does not cost much |
||
| 15 | 2 | Maximilian Seesslen | ** The signal is already there. It might be usefull to inspect the board |
| 16 | |||
| 17 | h2. Buchsen |
||
| 18 | |||
| 19 | * GND |
||
| 20 | * Durchgang |
||
| 21 | * PWM out |
||
| 22 | * PWM in to buzzer |
||
| 23 | * LED/BL in to big LED |
||
| 24 | |||
| 25 | * 2xJST-4; Kabeltest |
||
| 26 | |||
| 27 | Stiftleiste |
||
| 28 | |||
| 29 | * GND |
||
| 30 | * 3V |
||
| 31 | * 5V |
||
| 32 | * LED in 1 |
||
| 33 | * LED in 2 |
||
| 34 | * LED in 3 |
||
| 35 | * LED in 4 |
||
| 36 | |||
| 37 | * 2 Buzzers |
||
| 38 | * 1 Big LED |
||
| 39 | * Heardbeat |
||
| 40 | * User |
||
| 41 | * 1 Buzzer reset test |
||
| 42 | * 4 LEDs "open connection" |
||
| 43 | |||
| 44 | h2. MCU Pins |
||
| 45 | |||
| 46 | * 4 GPIO out cable-test |
||
| 47 | * 4 GPIO Input test |
||
| 48 | * 4 GPIO LEDs |
||
| 49 | * 1 LED "Running" amber |
||
| 50 | * 1 LED "Good" green |
||
| 51 | * 1 LED "Failed" red |
||
| 52 | * 1 LED "Not 1:1" orange |
||
| 53 | * PWM buzzer |
||
| 54 | * Button start testing |
||
| 55 | * 2 LEDs HB, User |
||
| 56 | |||
| 57 | 20 Pins; STM32G030C8T6 Cheap and boring LQFP48; |
||
| 58 | |||
| 59 | 2 Uart |
||
| 60 | 2 I2C |
||
| 61 | 2 Pow |